News
Catching Additive Manufacturing Flaws with Nanoseconds to Spare
Additive manufacturing has significant potential to strengthen the United States’ manufacturing base, but flaws within additively manufactured parts are preventing widespread adoption. ֱ APL experts are addressing this issue by developing sensors capable of identifying and preventing these flaws before they occur.
Credit: ֱ APL
The United States is on the cusp of a manufacturing renaissance. Federal legislation has ushered in billions of dollars of investment in manufacturing capabilities that will streamline the supply chain and . One capability poised to have a profound impact on the nation’s industrial base is additive manufacturing, which encompasses a variety of fabrication techniques that build structures layer by layer.
“Additive manufacturing allows you to create so many different structures that are optimized for specific applications,” said Vince Pagán, an experimental optics scientist and project manager at the ֱ Applied Physics Laboratory (APL) in Laurel, Maryland. “But its Achilles’ heel is that the process generates flaws that can cause parts to weaken and fail, and you can’t have that when they’re used in critical applications like national defense, biotechnology and aerospace.”
This problem remains one of the most significant obstacles to widespread adoption of additive manufacturing technology, but APL experts are addressing it by developing sensors that are fast enough to identify flaws before they materialize. The work builds on years of research supported by internal funding as well as the , the Army Research Laboratory and, most recently, the Office of Naval Research.
“If we can identify flaw formation while still in the melt state, then we have the opportunity to repair these imperfections before they result in performance-limiting flaws,” said Morgan Trexler, who leads APL’s Science of Extreme and Multifunctional Materials program. “We are working to make manufacturing processes more intelligent, which will inherently lead to more rapid manufacturing and trusted components.”
Bubble Trouble
Some of the most common flaws created during additive manufacturing — and among the hardest to prevent — are keyhole formations. These appear during the process of powder bed fusion, a method of additive manufacturing that uses lasers to melt metal powders and solidify them into complex geometries. When the lasers deposit too much energy too quickly into the melted metal or melt pool, tiny bubbles of vapor form and become trapped as the metal cools, weakening a part’s structural integrity. Because they form beneath actively printed layers, keyhole flaws are hard to spot in real-time — but not impossible.
“We can identify rocks below the surface of rivers from space, not because we can actually see them directly, but because we can see rapids where the water flow is disrupted,” explained Steve Storck, project manager and chief scientist for manufacturing technologies in APL’s Research and Exploratory Development Department. “Similarly, if a pore is about to form in a part, then the thermal flow around it will be disrupted, which indicates a flaw in the formation process. If we can measure that temperature and spectral anomalies accurately and rapidly, we should be able to tell if something is forming in, underneath or adjacent to the active melting location.”
The researchers hypothesized that these keyhole flaws were occurring during transitional states. If they could pause the depositing laser just before the anomaly began to form, then the molten metal could cool long enough to settle and close the vapor depression, preventing bubble formation.
“To eliminate keyhole flaws, we need to be able to detect and prevent them in real time, but this all happens exceptionally fast,” said Storck. “In the additive manufacturing process, solidification happens about one to three thousand times faster than during traditional processes, which means conventional sensing and control methods would not work. This drove us to develop custom methods.”
To find out just how long they needed to pause the laser, Li Ma, a senior engineer and additive manufacturing process modeling expert, ran a simulation using computational fluid dynamics. The simulation determined that response times faster than 10 to 20 microseconds were required to identify a thermal disruption, augment the process, and let the molten pool cool slightly without a flaw forming.
“This is where the magic happens,” said Pagán. “We’re essentially slowing down time.”
A model view of a keyhole flaw forming. The slide that is farthest to the right shows vapor trapped within the cooling metal. APL is aiming to prevent flaws like this through development of novel sensing methods that detect the anomalies before they fully form.
Credit: ֱ APL
From Concept to Process
The team first tested conventional sensors to see if they could identify the flaw signatures fast enough, but ran into optical resolution and speed limitations. This prompted a collaboration with , an associate professor of electrical and computer engineering with the ֱ University’s Whiting School of Engineering, and several Whiting School postdoctoral students to enhance an APL-developed and sensor. Melding expertise in materials science, additive manufacturing, optical engineering and data science, they added photodiodes at multiple wavelengths and increased the sample frequency to measure high spatial- and temporal-resolution data on the melt pool and its dynamics, enabling them to gather the information needed to identify the early stages of a keyhole flaw on a timescale that could enable real-time repair.
With the high-speed sensor up and running, the researchers developed a control framework that could communicate between the sensor and the laser and tell the laser to shut off when the melt pool got too hot and was likely to create a flaw — all within 10 to 20 millionths of a second.
Continuing to draw on expertise from across APL, Storck and Pagán reached out to developer Mike Brown, who adapted a high-speed field-programmable gate array — essentially an integrated circuit that can be programmed to meet specific needs — that was originally designed for defense purposes, to seek missiles in the sky.
“One of the unique aspects of working at APL is the ability to leverage technology from areas that seemingly do not relate; for example, we can take the knowledge and expertise we apply to missile defense — responding to measurement inputs very quickly and making adjustments even faster — and apply it to additive manufacturing,” said Storck.
After integrating all the systems, the team successfully demonstrated the system’s ability to respond in a mere 952 nanoseconds — less than one microsecond, or faster than the blink of an eye.
“Those were great results, because at a minimum we need to measure at least twice as fast as what’s actually happening physically, so we can capture the peaks and valleys of the spectral response as it correlates to temperature,” Storck explained. “Our system can measure the spectral and temperature readings and respond 10 times faster than required based on simulations of keyhole formation.”
The team plans to incorporate artificial intelligence into the process to speed up the feedback loop and more accurately indicate where and how the flaws are forming. Storck said this will enable real-time control and repair as APL works toward producing parts that can be trusted straight from the build.
The project undertaken is sponsored by the Department of the Navy, Office of Naval Research, under ONR award number N00014-22-1-2687. Any opinions, findings, and conclusions or recommendations expressed in this material are those of the author(s) and do not necessarily reflect the views of the Office of Naval Research.
Research was sponsored by the Hopkins Extreme Materials Institute and the Army Research Laboratory and was accomplished under Cooperative Agreement Number W911NF-20-2-0281. The views and conclusions contained in this document are those of the authors and should not be interpreted as representing the official policies, either expressed or implied, of the Army Research Laboratory or the U.S. government. The U.S. government is authorized to reproduce and distribute reprints for government purposes notwithstanding any copyright notation herein.
Related Event
Location: Building 201 (11091 ֱ Road, Laurel, Maryland 20723)
September 5, 2024 // 8 a.m. – 6 p.m.
APL will be hosting the Accelerating Materials Discovery for National Security Symposium on September 5, 2024, with the goal of bringing together government, leading materials experts and researchers, and innovators from a range of disciplines. These subject-matter experts will delve into identifying challenges and solutions addressing the pressing needs of extreme environments, such as space exploration, deep-sea exploration, hypersonic flight, resource-constrained scenarios, and harsh industrial applications. This event is only open to U.S. citizens. Registration opens in May.